-
TP4056 Type-C Lithium Battery 18650 Charger Module 1A With Battery Protection Type C BMS
- The input voltage: 4.35-6 v (recommended voltage 5 v)
- Charge cut-off voltage: 4.2 V + / – 1%
- Maximum charging current output: 1000 ma
- The battery overcharge protection voltage: 4.28 V
- Battery overcharge lifting voltage: 4.00 V
- The battery discharge protection voltage: 3.0 V
- Battery discharge termination voltage: 3.2 V
- Battery: over-current protection current 3 a
- The board size: about 2.5 * 1.65 CM
- Light state: no load the light not bright, red light for recharging, is full of green light.
₨ 55 -
ULTRA-FAST CHARGE: DUAL USB POWER BANK MOTHERBOARD MODULE
-
⚡ DUAL USB-A OUTPUT: Charge two devices simultaneously with high-efficiency power distribution.
-
🔄 USB TYPE-C BIDIRECTIONAL: Modern Type-C port supports both input (charging the power bank) and output (charging your phone).
-
📱 SMART DEVICE RECOGNITION: Automatically detects your device’s charging protocol to deliver the fastest possible current without damaging the battery.
-
🔋 LED STATUS INDICATORS: Integrated 4-LED display provides real-time battery level monitoring at a glance ($25\%$, $50\%$, $75\%$, $100\%$).
-
🛠️ BUILT-IN SAFETY SUITE: Includes over-charge protection, over-discharge protection, short-circuit prevention, and thermal shutdown.
-
🔌 MICRO-USB INPUT: Added compatibility for older charging cables, ensuring you can top up your power bank anywhere.
-
🧱 ROBUST DIY DESIGN: Clearly labeled B+ and B- soldering points for a secure connection to your 3.7V Lithium-Ion or Li-Po battery bank.
₨ 180 -
-
3S 4A 12.6V Lithium Battery Charger Module | USB Type-C to 12.6V Boost Converter for 18650 Li-Ion LiPo Batteries
-
🔋 Supports 3S Li-Ion / LiPo Battery Packs (12.6V charging output)
-
⚡ Input Voltage: DC 3V to 6V (recommended 3.7V–5V)
-
🔌 USB Type-C Input Port for convenient and universal charging
-
📈 High-Efficiency Boost Converter with switching frequency up to 1MHz
-
🧠 Quasi-CV Mode: Compensates for battery and trace resistance
-
🔄 Automatic Recharge when battery voltage drops
-
🔐 Built-in Protection: Over-voltage, short battery, and low-voltage input
-
💡 LED Indicators: “CR” for Charging, “OK” for Fully Charged or Constant Voltage Mode
-
🌡️ Wide Operating Temp: -40℃ to +85℃
-
🛠️ Compact Size: 39mm x 18mm x 6.3mm — ideal for tight DIY spaces
-
⚖️ Lightweight: Only 5g — perfect for portable use
₨ 195 -
-
12V 2A 24W AC to DC Power Supply Adapter
- Widely used for home decoration use,Car,hotels,clubs ,shopping malls.
- Wide input range,high precision voltage
- Overload protection
- Short circut protection
- Over temperatureprotection
- Saving Power
- Input: 100V~240V , 50~60Hz
- Output: DC 12V 2A / 1000mA
- DC plug size Outer Diameter: 5.5mm . Inner Diameter: 2.1mm
- Plug Specifications: EU Plug
- The adapters Connector: inside positive (+) . outside negative (-)
₨ 250 -
1S 3.7V 3A BMS PCM battery protection board for 18650 lithium ion li battery
- high-accuracy voltage detection circuit;
- terminal of the charger using high voltage device;
- Built-in three-stage over-current detection circuit (over-current 1, over-current 2, load short circuit);
- MOS transistor can control the battery charge and discharge;
- Over charge voltage: 4.25±0.05V
- Over charge release voltage:4.23±0.05V
- Over discharge voltage:2.54±0.1V
- Maximal continuous charging current: 2A
- Maximal continuous Discharging current: 2A
- Over current protection: 3A
- Size: L40*W4*T3mm
- Weight: 10g
₨ 45 -
DIY Power Bank Motherboard: High-Efficiency Charging Module with Type-C, Micro-USB & Lightning Inputs
-
DIY power bank charging & discharging control module
-
Supports Micro-USB & Type-C input (5V)
-
Dual USB-A output ports for charging two devices simultaneously
-
Output ratings: 5V / 1A and 5V / 2.1A
-
Compatible with 3.7V Li-ion / Li-Po batteries
-
Recommended for 18650 battery cells
-
Built-in battery protection & charging management
-
Compact slim PCB design for easy installation
-
Ideal for DIY electronics projects, portable chargers, and repairs
₨ 165 -
-
Power Bank Module | Bidirectional QC 3.0 & PD | Dual USB-A + Type-C DIY Motherboard
-
Dual-Port Output
Equipped with two high-current USB-A ports, allowing you to charge multiple devices simultaneously with stable power delivery. -
Bidirectional USB-C Port
The Type-C port supports both input (battery charging) and output (device charging), compatible with modern fast-charging standards. -
18W Fast Charging Support
Supports multiple fast-charge protocols including QC 3.0, QC 2.0, FCP, AFC, and MTK PE+ for rapid and efficient charging. -
Advanced Safety Protection
Built-in protection against over-charging, over-discharging, short circuits, and overheating, ensuring battery and device safety. -
High Conversion Efficiency
Uses a synchronous boost switch architecture with up to 95% power conversion efficiency, reducing energy loss and heat. -
Intelligent User Interface
Features 4 onboard LED indicators for real-time battery level display and a side-mounted function button for easy operation. -
Compact DIY-Friendly Design
Ultra-thin PCB with 3mm mounting holes, ideal for integration into custom 3D-printed or acrylic power bank enclosures.
₨ 175 -
-
3.7V Li-Ion Battery Charging and DC-DC Step Up Booster Module | Micro USB Input | Adjustable 4.2V–27V Output | TP4056 + MT3608
🔋 Dual Functionality:
Works as both a 3.7V Li-ion battery charger and a DC-DC step-up booster.⚡ Wide Input Range:
Accepts input voltage from 4.5V to 8V DC (via Micro USB or IN+ / IN− pins).🔧 Adjustable Output Voltage:
Provides 4.2V to 27V DC output, adjustable through the onboard potentiometer.🛡️ Safe & Reliable Charging:
Equipped with TP4056 chip for precise charging control and overcharge protection.🚀 High Efficiency Boost Converter:
MT3608-based step-up circuit offers stable output and excellent energy conversion.🔌 Compact & Easy to Use:
Small 3.3×2.3 cm size—ideal for DIY kits, prototyping, and portable devices.🌞 Solar Compatible:
Can be powered directly from 5V solar panels for outdoor or off-grid setups.💡 Multiple Applications:
Perfect for powering Wi-Fi routers, LED lights, fans, audio amps, RC projects, and more.₨ 165 -
35W 2S Fast Charging Power Bank Module | QC 3.0 | DIY 7.4V Lithium Battery Charger PCB with LED Display & BMS
-
🔥 35W ULTRA-FAST OUTPUT: Rapidly charges smartphones and tablets, supporting high-wattage single-port delivery.
-
⚡ MULTI-PROTOCOL SUPPORT: Fully compatible with SuperVooC, QC 3.0, PD 3.0, and Samsung PPS for universal fast charging.
-
🔋 2S SERIES OPTIMIZED: Designed for 7.4V/8.4V Lithium Battery setups (2x 18650 or 21700 cells in series).
-
📱 TRIPLE-PORT DESIGN: Includes 2x USB Type-C and 1x USB Type-A ports to power multiple devices simultaneously.
-
🛡️ INTEGRATED SAFETY BMS: Features built-in protection against over-charging, over-discharging, and short circuits.
-
🌡️ ACTIVE THERMAL MONITORING: Comes with a pre-wired NTC Heat Sensor to monitor battery temperature during high-speed operation.
-
🔢 SMART DIGITAL DISPLAY: A bright LED readout provides instant visibility of the battery percentage and charging status.
-
📐 MINIATURE FORM FACTOR: Measuring only 45mm x 20mm, it easily fits into compact 3D-printed or custom enclosures.
₨ 299 -
